| Parte n. | Fabbricante | Applicazione |
|---|
| MAX207CAG | MaximIC | +5V RS-232 transceiver with 0.1 microF external capacitors |
| MAX4582CEE | MaximIC | Low-voltage, CMOS analog multiplexer (two 4-channel). |
| MAX379EWG | MaximIC | High-voltage, fault-protected analog multiplexer. |
| MAX487EPA | MaximIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 0.25Mbps. Slew-rate limited - yes. Low-power shutdown - yes. Receiver/driver enable - yes. Quiescent current - 120 microA. Number of transmitter on bus - 128. |
| MAX972CPA | MaximIC | Ultra-low-power, open-drain, dual comparator. Internal precision reference none. Internal hysteresis no. |
| MAX1246ACEE | MaximIC | +2.7V, low-power, 4-channel, serial 12-bit ADC. INL (LSB) +1/2,-1/2 |
| MAX1617MEE | MaximIC | Remote/local temperature sensor with SMBus serial interface |
| MAX6318MHUK29CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.930V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
| ICL7642CMJD | MaximIC | Quad operational amplifier, 10mV |
| MXL1001ACS8 | MaximIC | Precision operational amplifier |
| MAX6326XR30-T | MaximIC | Ultra-low-power microprocessor supervisory circuit (reset output active-low, push-pull). Reset threshold (typ) 3.000V. Order increment 10k |
| MAX6317HUK34CX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.400V, min reset timeout 140ms, typ watchdog timeout 102ms |
| MAX6313UK35D3-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 3.413(min) 3.588(max).Nominal timeout period 140ms. |
| MAX6321HPUK46CW-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.630V, reset timeout(min) 140ms, watchdog timeout(typ) 6.3ms |
| MAX6319LHUK26D-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 2.630V, reset timeout(min) 1120ms |
| MX7545ATQ | MaximIC | TTL/CMOS compatible for Vdd = 5V or CMOS compatible for Vdd = 15V, 12-bit buffered multiplying DAC. Gain error +-3 LSB. |
| MAX477EUA | MaximIC | 300MHz high-speed op amp. |
| MAX199BCAI | MaximIC | Multi-range (+-4V, +-2V, +4V, +2V), +5V supply, 12-bit DAS with 8+4 bus interface |
| MAX8866SEUA | MaximIC | Dual, low-dropout, 100mA linear regulator with auto-discharge function. Preset output voltage 2.84V |
| MAX803TEXR-T | MaximIC | Microprocessor reset circuit Reset threshold 3.08V. Open-drain active-low reset. 2.5k increments. |
| MAX1542ETP | MaximIC | TFT LCD DC-to-DC converter with operational amplifiers |
| MAX6318LHUK37BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.700V min, reset timeout 20ms,typ watchdog timeout 25.6sec |
| MAX184BC/D | MaximIC | High-speed 12-bit A/D converter with external reference input. 5 microsec. max conversion time. Linearity(LSB) +-1. |
| MAX466CNI | MaximIC | Two-channel, quad RGB switch and buffer. Voltage gain 2V/V. |
| MAX520ACPE | MaximIC | Quad, 2-wire serial 8-bit DAC with Rail-to-Rail, unbuffered outputs. TUE(LSB) 1. |
| MAX6318MHUK49AY-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.900V, reset timeout(min) 1ms, watchdog timeout(typ) 1.6sec |
| MAX789CCK | MaximIC | 3V 5A step-down, PWM, switch-mode DC-DC regulator. |
| MAX6318MHUK42CX-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.200V, reset timeout(min) 140ms, watchdog timeout(typ) 102ms |
| MAX786C/D | MaximIC | Dual-output power-supply controller for notebook computers |
| MAX814NCSA | MaximIC | +-1% accuracy, low-power, microprocessor supervisory circuit. Reset trip threshold (min) 4.50V (max) 4.60V, push-pull active-low reset output, push-pull active-high reset output, manual reset, power-fail monitor, low-line detector. |
