| Parte n. | Fabbricante | Applicazione |
|---|
| MAX6318LHUK43BX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.300V min, reset timeout 20ms,typ watchdog timeout 102ms |
| DG403DJ | MaximIC | Improved, dual, SPDT, two NO and two NC switches, high-speed analog switch. |
| MAX777LCPA | MaximIC | Low-voltage input, step-up DC-DC converter |
| MAX549ACPA | MaximIC | +2.5V to +5.5V, low-power, dual, 8-bit voltage-output DAC with an external reference input. |
| MAX1242AMJA | MaximIC | +2.7V to +5.25V, low-power, 10-bit serial ADCs in SO-8. INL (LSB) +1/2 |
| ICL7665BCSA | MaximIC | Microprocessor voltage monitor with dual overvoltage and undervoltage detection |
| MAX6332UR18D1-T | MaximIC | Ultra-low-voltage, low power microprocessor reset circuit. Reset threshold(typ) 1.8V, reset timeout(min) 1ms. |
| MAX6316MUK46DY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.630V, min reset timeout 1120ms, typ watchdog timeout 1.6ms |
| IH5044MJE | MaximIC | General-purpose CMOS analog switch. Double pole, single throw (DPST) |
| MAX470CWE | MaximIC | Two-channel, quad video buffer. Voltage gain 2V/V. |
| MAX6198BESA | MaximIC | Precision, micropower, low-dropout voltage reference. Output voltage 4.096V, initial accuracy +-5, temperature coefficient <10ppm. |
| MAX182ACPI | MaximIC | Calibrated 4-channel 12-bit ADC with T/H and reference. |
| MAX6321HPUK35CY-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.500V, reset timeout(min) 140ms, watchdog timeout(typ) 1.6sec |
| MAX6321HPUK29CY-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.930V, reset timeout(min) 140ms, watchdog timeout(typ) 1.6sec |
| MAX6316MUK41AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.100V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
| MAX4427C/D | MaximIC | Dual high-speed, 1.5A MOSFET driver. 4.5V t0 18V operation range. |
| MAX4546EPE | MaximIC | Dual,low-voltage T-switch designed for switching RF and video signals from DC to 300MHz in 50om and 75om systems. |
| MAX793SEPE | MaximIC | Microprocessor supervisory circuit. Reset threshold 2.85V to 3.00V. Active-low reset.Active-high reset.Low-line early warning output.Backup-battery switchover.External switch driver.Power-fail comparator.Battery OK output.Watchdog input.Manual reset inp. |
| MX7531JN | MaximIC | CMOS 12 bit multiplying D/A converter. Error 0.2% |
| MXD1000SE75 | MaximIC | 5-tap silicon delay line |
| MAX6316MUK40AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.000V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
| MAX9052AESA | MaximIC | Micropower, single-supply, dual comparator + precision reference IC. |
| MAX4274BKESA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 50, 1+ (Rf/Dg) noninverting gain 51, -3dB BW 330kHz. |
| MAX1487C/D | MaximIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 230 microA. Number of transmitter on bus - 128. |
| MX7506KN | MaximIC | Single, 16 channel (1 of 16) monolithic CMOS analog multiplexer. |
| MAX3491EESD | MaximIC | 3.3V-powered, +-15kV ESD-protected, 15Mbps and slew-rate-limited true RS-485/RS-422 transceiver. Guaranteed data rate 12Mbps. Supply voltage 3.0V to 3.6V |
| MAX160CWN | MaximIC | Microprocessor compatible 8-bit A/D converter. Fast conversion time 4microsec. Error +-1/2 LSB. |
| MAX182BC/D | MaximIC | Calibrated 4-channel 12-bit ADC with T/H and reference. |
| MAX6318MHUK43DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.300V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX4175AHEUK-T | MaximIC | Single, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 2.5, 1+ (Rf/Dg) noninverting gain 3.5, -3dB BW 820kHz. |
