| Parte n. | Fabbricante | Applicazione |
|---|
| MAX6315US40D1-T | MaximIC | Open-drain microprocessor reset circuit. Reset threshold(nom) 4.00V. Reset timeout period(min) 1ms. |
| DG300C/D | MaximIC | "Dual, TTL compatible CMOS analog switche" |
| MAX706C/D | MaximIC | "Low-cost, microprocessor supervisory circuit. Active-low manual reset input. Independent watchdog timer - 1.6s timeout. Precision supply-voltage monitor 4.4V." |
| MAX663CPA | MaximIC | Dual Mode 5V or programmable micropower voltage positive regulator. |
| MAX485C/D | MaximIC | "Low-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 300 microA. Number of transmitter on bus - 32." |
| MAX6305UK00D2-T | MaximIC | "Multiple-input, programmable reset IC (open-drain reset output, 2 additional undervoltage reset inputs). Nominal timeout period 20ms." |
| MAX5035AUSA | MaximIC | "1A, 76V, high-efficiency MAXPower step-down DC-DC converter, output 3.3V" |
| MAX358C/D | MaximIC | Fault-protected analog 8 channel single-ended (1 of 8) multiplexer. |
| ICL7631BMJE | MaximIC | "Triple operational amplifier, 5mV" |
| MAX466ENI | MaximIC | "Two-channel, quad RGB switch and buffer. Voltage gain 2V/V." |
| MAX1242ACPA | MaximIC | "+2.7V to +5.25V, low-power, 10-bit serial ADCs in SO-8. INL (LSB) +1/2" |
| MAX6319MHUK36A-T | MaximIC | "Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.600V, reset timeout(min) 1ms" |
| MAX6318LHUK30BY-T | MaximIC | "Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.000V min, reset timeout 20ms, typ watchdog timeout 1.6sec" |
| MAX174BEWI | MaximIC | Industry standard complete 12-bit A/D converter. 8 microsec. max conversion time. Linearity (LSBs) 1/2. TEMPCO(ppm/C) 38. |
| MAX742EPP | MaximIC | Switch-mode regulator with +5V to +-12V or +-15V dual output. |
| MAX6320PUK47AX-T | MaximIC | "Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.700V, reset timeout(min) 1ms, watchdog timeout(typ) 102ms" |
| MX7528LCWP | MaximIC | CMOS dual 8 bit buffered multiplying DAC. +5V to 15V single supply operation. Error +-1/2 LSB. |
| MAX6318LHUK42AX-T | MaximIC | "Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.200V min, reset timeout 1ms,typ watchdog timeout 102ms" |
| MAX6316LUK46AZ-T | MaximIC | "Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.630V, min reset timeout 1ms, typ watchdog timeout 25.6sec" |
| MAX923EPA | MaximIC | "Dual micropower, low-voltage comparator. Intarnal 1.182V+-1% voltage reference. Internal programmable hysteresis." |
| MAX6318MHUK41DW-T | MaximIC | "Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.100V, reset timeout(min) 1.12sec, watchdog timeout(typ) 6.3ms" |
| MAX6319MHUK40D-T | MaximIC | "Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.000V, reset timeout(min) 1120ms" |
| MAX689EPA | MaximIC | "High-accuracy, low-dropout linear regulator" |
| MAX271CNG | MaximIC | "Digitally-programmed, dual 2nd-order continuous lowpass filter." |
| MAX4534EUD | MaximIC | "Fault-protected, high-voltage, single 4-to-1 multiplexer operated with +-4.5V to +-20V dual supply or a +9V to +39V single supply." |
| MAX6321HPUK26CZ-T | MaximIC | "Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.630V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec" |
| MAX1247AEPE | MaximIC | "+2.7V, low-power, 4-channel, serial 12-bit ADC. INL (LSB) +1/2,-1/2" |
| MAX6318LHUK45CZ-T | MaximIC | "Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.500V min, reset timeout 140ms,typ watchdog timeout 25.6sec" |
| MAX309EPE | MaximIC | "Precision, dual 4-channel, high-performance, CMOS analog multiplexer." |
| ICL7662MTV-4 | MaximIC | CMOS voltage converter |
