| Parte n. | Fabbricante | Applicazione |
|---|
| MAX487CUA | MaximIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 0.25Mbps. Slew-rate limited - yes. Low-power shutdown - yes. Receiver/driver enable - yes. Quiescent current - 120 microA. Number of transmitter on bus - 128. |
| MAX6316MUK40AW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 4.000V, min reset timeout 1ms, typ watchdog timeout 6.3ms |
| MAX1457CWI | MaximIC | 0.1%-accurate signal conditioner for piezoresistive sensor compensation. |
| MAX6320PUK35CW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.500V, reset timeout(min) 140ms, watchdog timeout(typ) 6.3ms |
| MAX167CENG | MaximIC | CMOS 12-bit A/D converter with track-and-hold. Error +-1 LSB. |
| MAX1205CMH | MaximIC | +5V single-supply, 1Msps, 14-bit self-calibrating ADC |
| MAX361CSE | MaximIC | Precision, quad, SPST analog switch. |
| MAX6318LHUK36AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.600V min, reset timeout 1ms,typ watchdog timeout 25.6sec |
| MAX802SCPA | MaximIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 2.925V. Active-low reset. Watchdog input. Backup-battery switch. Power-fail threshold accuracy +-2%. Power-fail comparator. Reset window +-2% |
| MAX4075BHESA | MaximIC | Micropower, Rail-to-Rail, fixed-gain, dual, GainAmp op amp. Inverting gain 40V/V, noninverting gain 41V/V, -3dB BW 67kHz. |
| MAX6318MHUK45DX-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.500V, reset timeout(min) 1.12sec, watchdog timeout(typ) 102ms |
| MX7541AJP | MaximIC | CMOS 12 bit multiplying D/A converter. Error 1 LSB. |
| MAX6319LHUK33D-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 3.300V, reset timeout(min) 1120ms |
| REF01AJ | MaximIC | +10V precisioon voltage reference. Max TEMPCO 8.5ppm/degC. Initial error +-30mV |
| MAX469CWE | MaximIC | Two-channel, triple video buffer. Voltage gain 2V/V. |
| MAX6332UR25D1-T | MaximIC | Ultra-low-voltage, low power microprocessor reset circuit Reset threshold(typ) 2.5V, reset timeout(min) 1ms |
| MAX251C/D | MaximIC | +5V powered isolated RS-232 driver/receiver. |
| MAX793TESE | MaximIC | Microprocessor supervisory circuit. Reset threshold 3.00V to 3.15V. Active-low reset.Active-high reset.Low-line early warning output.Backup-battery switchover.External switch driver.Power-fail comparator.Battery OK output.Watchdog input.Manual reset inp. |
| MAX933CUA | MaximIC | Dual low-power, low-cost comparator with intarnal 1.182V+-2% bandgap reference and internal programmable hysteresis.. |
| MAX6322HPUK27D-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.700V, reset timeout(min) 1120ms |
| MAX811SEUS-T | MaximIC | Microprocessor voltage monitor with manual reset input. Reset threshold voltage 2.93V |
| MAX788ECK | MaximIC | 3.3V 5A step-down, PWM, switch-mode DC-DC regulator. |
| MAX688ESA | MaximIC | High-accuracy, low-dropout linear regulator |
| DG412C/D | MaximIC | Improved, quad, SPST analog switches |
| MAX6336US19D2-T | MaximIC | Ultra-low-voltage, low-power microprocessor circuit with manual reset (reset output active-low, push/pull . Reset threshold(typ) 1.9V, reset timeout(min) 20ms. |
| MAX3483ESA | MaximIC | 3.3V-powered, 10Mbps and slew-rate-limited true RS-485/RS-422 transceiver. Guaranteed data rate 0.25Mbps. Supply voltage 3.0V to 3.6V |
| MAX6317HUK41BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.100V, min reset timeout 20ms, typ watchdog timeout 25.6sec |
| MAX821UUS-T | MaximIC | Microprocessor voltage monitor with pin-selectable power-on reset timeout delay (1ms,max, 20ms,min or 100ms,min). Reset threshold(nom) 2.78V. Active-low reset output. |
| MAX6316LUK36DW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.600V, min reset timeout 1.12sec, typ watchdog timeout 6.3ms |
| MAX6379XR44-T | MaximIC | Ultra-low-power voltage detector, 4.4V |
