| Parte n. | Fabbricante | Applicazione |
|---|
| MAX1259EWE | MaximIC | Battery manager |
| MAX6317HUK28BW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 2.800V, min reset timeout 20ms, typ watchdog timeout 6.3ms |
| MX7248SQ | MaximIC | Complete, 12-bit voltage-output DAC. |
| MAX6318LHUK46BW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.630V min, reset timeout 20ms,typ watchdog timeout 6.3ms |
| MAX6321HPUK27DX-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.700V, reset timeout(min) 1.12sec, watchdog timeout(typ) 102ms |
| MAX1665XESA | MaximIC | Lithium-ion battery pack protector. Cell count 4 |
| MAX4120ESD | MaximIC | Quad, 300MHz -3dB bandwidth, low-power, current feedback amplifier. |
| MAX485ESA | MaximIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 300 microA. Number of transmitter on bus - 32. |
| MAX189CCPA | MaximIC | +5V, low-power, 12-bit serial ADC. Error(LSB) +-2. |
| MAX6327XR23-T | MaximIC | Ultra-low-power microprocessor supervisory circuit (reset output active-high, push-pull). Reset threshold (typ) 2.320V. Standard version. Order increment 2.5k |
| MAX6318MHUK32BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.200V, reset timeout(min) 20ms, watchdog timeout(typ) 25.6sec |
| MAX4074ABESA | MaximIC | Micropower, Rail-to-Rail, fixed-gain, single, GainAmp op amp. Inverting gain 0.25V/V, noninverting gain 1.25V/V, -3dB BW 200kHZ. |
| MX7548TD | MaximIC | CMOS 8-bit microprocessor compatible 12-bit DAC. Linearity +-1/2 LSB. |
| MAX6318LHUK27CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 2.700V min, reset timeout 140ms, typ watchdog timeout 25.6sec |
| MAX389EJN | MaximIC | High-voltage, fault-protected analog multiplexer. 4-channel differential (2 of 8). |
| MAX6318LHUK31CY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.080V min, reset timeout 140ms, typ watchdog timeout 1.6sec |
| MAX6321HPUK36AX-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.600V, reset timeout(min) 1ms, watchdog timeout(typ) 102ms |
| ICL7109CPL | MaximIC | 12 bit A/D converter with 3-state binary outputs |
| MAX336EPI | MaximIC | 16-channel, low-leakage, CMOS analog multiplexer. |
| MX7541AJCWN | MaximIC | CMOS 12 bit multiplying D/A converter. Error 1 LSB. |
| MAX6354TYUT-T | MaximIC | Dual-voltage microprocessor supervisory circuit with manual reset. Reset threshold 3.08V (Vcc5) and 2.19V (Vcc3). Active-low push-pull reset 3V. |
| MAX6316LUK45AY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.500V, min reset timeout 1ms, typ watchdog timeout 1.6sec |
| MAX4628EUT-T | MaximIC | Low Ron 0.5om max(+5V supply), 0.9om max(+3V supply), low-voltage, single-supply(+1.8V to +5.5V) operation, NO, two control inputs, SPST analog switch. |
| MAX901ACSE | MaximIC | High-speed, low-power voltage comparator |
| MAX6306UK36D2-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual reset input). Factory-trimmed reset thresholds 3.510(min),3.690(max) Nominal timeout period 20ms. |
| MAX6317HUK35DW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.500V, min reset timeout 1.12sec, typ watchdog timeout 6.3ms |
| MAX6726KARHD3-T | MaximIC | Vcc1 2.625 V, Vcc2 1.313 V, active timeout period 140 ms-280 ms, dual/triple ultra-low-voltage SOT23 mP supervisor circuit |
| MAX6380XR46-T | MaximIC | Ultra-low-power voltage detector, 4.6V |
| MAX6313UK29D4-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 2.857(min) 3.000(max).Nominal timeout period 1120ms. |
| MAX846AC/D | MaximIC | Cost-saving multichemistry battery-charger system |
