| Parte n. | Fabbricante | Applicazione |
|---|
| MXL1007ACN8 | MaximIC | Low-noise, precision operational amplifier. |
| MAX6316LUK29AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.930V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
| MAX382MJN | MaximIC | Low-voltage, 8-channel multiplexer with latchable inputs. |
| MAX6318LHUK41AW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.100V min, reset timeout 1ms,typ watchdog timeout 6.3ms |
| MAX6317HUK32CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.200V, min reset timeout 140ms, typ watchdog timeout 25.6sec |
| MAX989ESA | MaximIC | Dual, low-power, Rail-to-Rail I/O comparator. Push/pull output stage sinks and sources. |
| MAX802RCPA | MaximIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 2.625V. Active-low reset. Watchdog input. Backup-battery switch. Power-fail threshold accuracy +-2%. Power-fail comparator. Reset window +-2% |
| MAX6333UR19D2-T | MaximIC | Ultra-low-voltage, low power microprocessor reset circuit. Reset threshold(typ) 1.9V, reset timeout(min) 20ms. |
| MAX6321HPUK26CW-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.630V, reset timeout(min) 140ms, watchdog timeout(typ) 6.3ms |
| MAX6320PUK29AW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 2.930V, reset timeout(min) 1ms, watchdog timeout(typ) 6.3ms |
| MAX6317HUK50AY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 5.000V, min reset timeout 1ms, typ watchdog timeout 1.6sec |
| MAX3771CEE | MaximIC | 1.063Gbps, 3.3V fibre channel repeater. |
| MAX4107ESA | MaximIC | Ultra-low-noise op amp. 300MHz-3dB bandwidth. 10V/V. |
| MAX521BCPP | MaximIC | Octal, 2-wire serial 8-bit DAC with Rail-to-Rail, unbuffered outputs. TUE(LSB) 2. |
| MAX6313UK27D3-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 2.633(min) 2.768(max).Nominal timeout period 140ms. |
| MAX6318LHUK44BW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.390V min, reset timeout 20ms,typ watchdog timeout 6.3ms |
| MAX637ACJA | MaximIC | Preset -15V output or adjuistable output with 2 resistors, CMOS switching regulator. Output accuracy 5%. |
| MAX6319MHUK49A-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.900V, reset timeout(min) 1ms |
| MAX3243ECWI | MaximIC | +-15kV ESD-protected, 1microA, 3.0 to 5.5V, 250kbps, RS-232 transceiver with AutoShutdown. |
| MAX481CSA | MaximIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - yes. Receiver/driver enable - yes. Quiescent current - 300 microA. Number of transmitter on bus - 32. |
| DG403DK | MaximIC | Improved, dual, SPDT, two NO and two NC switches, high-speed analog switch. |
| MAX3761EEP | MaximIC | Low-power, 622Mbps limiting amplifier with chatter-free power detect for LANs. |
| MAX4540CPP | MaximIC | Low-voltage, dual 4-to-1 calibration multiolexer. |
| MAX8862RESE | MaximIC | Low-cost, low-dropout, dual linear regulator. Fixed output voltage 2.85V |
| MAX6318LHUK27CW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 2.700V min, reset timeout 140ms, typ watchdog timeout 6.3ms |
| MAX809LEUR-T | MaximIC | Microprocessor reset circuit. Reset threshold 4.632V. Push-pull active-high reset. 2.5k increments. |
| ICL7611DC/D | MaximIC | Single operational amplifier, 15mV |
| MAX4543ESA | MaximIC | Low-voltage, single-supply dual SPST analog switch. |
| MAX6503UKP005-T | MaximIC | Low-cost, +2.7V to +5.5V micropower temperature switch. Output stage open-drain. Standard temperature threshold(C) +5. |
| MAX6375XR25-T | MaximIC | Ultra-low-power voltage detector, 2.5V |
