| Parte n. | Fabbricante | Applicazione |
|---|
| MAX4619CSE | MaximIC | Low-woltage, high-speed, CMOS analog IC configured as three SPDT switch. |
| MAX4518CPD | MaximIC | Precision, 4-channel, low-voltage, CMOS analog multiplexer. Single-supply operation (+2.2V to +15V) or bipolar-supply operation (+-2.2V to +-8V). |
| MXD1000C/D30 | MaximIC | 5-tap silicon delay line |
| MAX6316LUK36CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.600V, min reset timeout 140ms, typ watchdog timeout 25.6sec |
| MX674AKEPI | MaximIC | Industry standard complete 12-bit A/D converter. 15 microsec. max conversion time. Linearity (LSBs) 1/2. TEMPCO(ppm/C) 38. |
| MAX6321HPUK26AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 2.630V, reset timeout(min) 1ms, watchdog timeout(typ) 25.6sec |
| MAX933CPA | MaximIC | Dual low-power, low-cost comparator with intarnal 1.182V+-2% bandgap reference and internal programmable hysteresis.. |
| MAX6313UK28D4-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc, 1 additional undervoltage reset input,negative/overvoltage reset input).Factory-trimmed reset thresholds 2.730(min) 2.870(max).Nominal timeout period 1120ms. |
| MAX7401ESA | MaximIC | 8-th-order, lowpass, bessel, switched-capacitor filter. Single-supply operation +5V |
| MAX4275BEEUA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 24, 1+ (Rf/Dg) noninverting gain 25, -3dB BW 590kHz. |
| MXD1000SA150 | MaximIC | 5-tap silicon delay line |
| MAX1721EUT | MaximIC | Switched-capacitor voltage inverter with shutdown. |
| MAX6357MSUT-T | MaximIC | Triple-voltage microprocessor supervisory circuit with manual reset. Reset threshold 4.38V (Vcc5) and 2.93V (Vcc3). Active-low push-pull reset 3V. |
| REF02CSA | MaximIC | +5V precisioon voltage reference. Max TEMPCO 65ppm/degC. Initial error +-50mV |
| MAX1485CUB | MaximIC | Software-selectable, half-/full-duplex, slew-rate-limite 12 Mbps, RS-485/RS-422 transceiver. |
| MAX6312UK38D4-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 3.705(min) 3.895(max). Nominal timeout period 1120ms. |
| MAX873ACPA | MaximIC | Low-power, low-drift precision voltage reference. 2.5V+-1.5mV output (Ta=25gradC). TEMPCO(max) 7ppm/gradC. |
| MAX6318LHUK30AW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 3.000V min, reset timeout 1ms, typ watchdog timeout 6.3ms |
| MAX183ACNG | MaximIC | High-speed 12-bit A/D converter with external reference input. 3 microsec. max conversion time. Linearity(LSB) +-1/2. |
| MAX1005CEE | MaximIC | IF undersampler |
| MAX369EPN | MaximIC | Fault-protected analog multiplexer with latch. 4 channel differential (2 of 8). |
| MAX9698MJE | MaximIC | Single very fast TTL output comparator |
| MAX2463EAI | MaximIC | 900 MHz image-reject transceiver. |
| MAX1161BCPI | MaximIC | 10-bit, 40 Msps, TTL-output ADC |
| IH5140M/D | MaximIC | Low power fast CMOS analog switch. Single pole, single throw (SPST). |
| HI6-0201HS-9 | MaximIC | High-speed, CMOS, quad, SPST analog switch |
| MAX7233BFIQ | MaximIC | Triplexed LCD decoder/driver (4 alphanumeric characters/18 segments; parallel input format). |
| MAXC001 | MaximIC | 150 microF low-ESR aluminum electrolytic capacitor. Value 150 microF +-20%. |
| MAX6333UR23D3-T | MaximIC | Ultra-low-voltage, low power microprocessor reset circuit. Reset threshold(typ) 2.3V, reset timeout(min) 100ms. Standatd version |
| MAX6346XR40-T | MaximIC | Microprocessor supervisory circuit (reset output active-low, push-pull). Reset threshold (typ) 4.000V. Order increment 10k |
