Percorso:okDatasheet > Tutti i fornitori > MaximIC Scheda > MaximIC-150
H MAX629C/D MAX3262C/D MXL1014DN MAX159ACUA MAX6312UK26D2-T MAX6321HPUK40CZ-T MAX131CPL MAX385ESE MAX820RMJE MAX238MRG MAX922CSA MAX660CPA MXD1000PA20 MAX185AEWG MAX903MJA MAX3111EENI MAX398CSE MAX6316LUK25AZ-T MAX358MJE MAX4515ESA MAX118EAI MAX5253BEAP MXD1000C/D25 MAX1487EEPA M
Parte n. | Fabbricante | Applicazione |
---|---|---|
MAX831CWE | MaximIC | Fixed output 5V, 1A, step-down, PWM, switch-mode DC-DC regulator. |
MM74C945CQH | MaximIC | 4 digit up/down counter/decoder/driver. |
MAX629C/D | MaximIC | 28V, low-power, high-voltage, boost or inverting DC-DC converter. |
MAX3262C/D | MaximIC | 1Gbps, high-speed limiting amplifier with catter-free loss-of-signal detection. |
MXL1014DN | MaximIC | Quad precision op amp. |
MAX159ACUA | MaximIC | +2.7V, low-power, 2-channel, 108ksps, serial 10-bit ADC in 8-pin microMAX. INL (LSB) +,- 0.5 |
MAX6312UK26D2-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 2.564(min) 2.696(max). Nominal timeout period 20ms. |
MAX6321HPUK40CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.000V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
MAX131CPL | MaximIC | 3 1/2 Digit A/D converter with bandgap reference |
MAX385ESE | MaximIC | Precision, low-voltage analog switch. |
MAX820RMJE | MaximIC | Microprocessor and non-volatile metory supervisory circuit. Reset threshold 2.61V. Reset and low-line threshold accuracy +-2% |
MAX238MRG | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
MAX922CSA | MaximIC | Dual micropower, low-voltage comparator. |
MAX660CPA | MaximIC | CMOS monolithic voltage coverter |
MXD1000PA20 | MaximIC | 5-tap silicon delay line |
MAX185AEWG | MaximIC | High-speed 12-bit A/D converter with external reference input. 10 microsec. max conversion time. Linearity(LSB) +-1/2. |
MAX903MJA | MaximIC | High-speed, low-power voltage comparator |
MAX3111EENI | MaximIC | SPI/MICROWIRE-compatible UART and +-15kV ECD-protected RS-232 transceiver with internal capacitor. Single-supply operation +3.3V. Vcc (V) 3.3 |
MAX398CSE | MaximIC | Precision, 8-channel, low-voltage, CMOS analo0g multiplexer. |
MAX6316LUK25AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 2.500V, min reset timeout 1ms, typ watchdog timeout 25.6sec |
MAX358MJE | MaximIC | Fault-protected analog 8 channel single-ended (1 of 8) multiplexer. |
MAX4515ESA | MaximIC | Low-voltage, low-on-resistance, SPST, CMOS analog switch. Normally closed (NC), +2V to +12V single-supply operation. |
MAX118EAI | MaximIC | 5 V, 1Msps, 4-channel, 8-bit ADC |
MAX5253BEAP | MaximIC | +3V, quad, 12-bit, voltage-output DAC with serial interface. INL(LSB) +-1. |
MXD1000C/D25 | MaximIC | 5-tap silicon delay line |
MAX1487EEPA | MaximIC | +-15kV ESD-protected, low-power, RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 230 microA. Number of transmitter on bus - 128. |
MAX690EJA | MaximIC | Microprocessor supervisory circuit. |
MAX4621ESE | MaximIC | Low on-resistance 3om(typ), 5om(max), dual, SPST, NO analog switch. |
MAX6319MHUK30A-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.000V, reset timeout(min) 1ms |
MAX621EPN | MaximIC | Quad, high-side MOSFET driver |