| Parte n. | Fabbricante | Applicazione |
|---|
| MAX160MJN | MaximIC | Microprocessor compatible 8-bit A/D converter. Fast conversion time 4microsec. Error +-1/2 LSB. |
| MAX3042BEWE | MaximIC | +/-10kV ESD-protected, 5V quad RS-485/RS-422 transmitter |
| MAX381EPE | MaximIC | Precision, low-voltage analog switch. |
| MAX6312UK35D3-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 3.413(min) 3.588(max). Nominal timeout period 140ms. |
| MAX6321HPUK32AW-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.200V, reset timeout(min) 1ms, watchdog timeout(typ) 6.3ms |
| MAX188AMJP | MaximIC | Low-power, 8-channel, serial 12-bit ADC. |
| MAX184ACNG | MaximIC | High-speed 12-bit A/D converter with external reference input. 5 microsec. max conversion time. Linearity(LSB) +-1/2. |
| MAX6316MUK50DW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,bidirectional).Factory-trimmed reset threshold (typ) 5.000V, min reset timeout 1120ms, typ watchdog timeout 6.3ms |
| MAX643AC/D | MaximIC | +15V fixed output, 10W CMOS step-up switching regulator. 5% output accuracy |
| ICM7218BIPI | MaximIC | 8 digit LED display driver |
| MX7530JQ | MaximIC | CMOS 10 bit multiplying D/A converter. Error 0.2% |
| MAX6502CMP105-T | MaximIC | Low-cost, +2.7V to +5.5V micropower temperature switch. Output stage push-pull. Standard temperature threshold(C) +105. |
| MAX4373FESA | MaximIC | Low-cost, micropower, high-side current-sense amplifier + comparator + reference IC. Gain +50V/V. |
| MAX6319LHUK50A-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 5.000V, reset timeout(min) 1ms |
| MAX1720EUT | MaximIC | Switched-capacitor voltage inverter with shutdown. |
| MAX196ACAI | MaximIC | Multirange, single +5V, 12-bit DAS with 12-bit bus interface |
| MAX983CPA | MaximIC | Ultra-low-power, open-drain, dual comparator. Internal precision reference 2%. Internal hysteresis yes. |
| DG441DK | MaximIC | Improved, quad, SPST analog switch |
| MAX6315US37D4-T | MaximIC | Open-drain microprocessor reset circuit. Reset threshold(nom) 3.70V. Reset timeout period(min) 1120ms. |
| MAX4174ANEUK-T | MaximIC | Single, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 8, 1+ (Rf/Dg) noninverting gain 9, -3dB BW 480kHz. |
| MAX675EPA | MaximIC | +5V precision voltage reference. Temp. coefficient 15ppm/degC, Initial error 7mV. |
| MAX4507CAP | MaximIC | Fault-protected, high-voltage, signal-line protector |
| MAX4175AEEUK-T | MaximIC | Single, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 1.25, 1+ (Rf/Dg) noninverting gain 2.25, -3dB BW 450kHz. |
| MAX6317HUK30BW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.000V, min reset timeout 20ms, typ watchdog timeout 6.3ms |
| MAX491EPD | MaximIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Full-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 300 microA. Number of transmitter on bus - 32. |
| MAX6306UK38D4-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual reset input). Factory-trimmed reset thresholds 3.705(min),3.895(max) Nominal timeout period 1120ms. |
| MX7541J/D | MaximIC | CMOS 12 bit multiplying D/A converter. Error 1 LSB. |
| MAX7412CPA | MaximIC | 5th-order, lowpass, elliptic, switched-capacitor filter. Transition ratio r = 1.6, operating voltage +3V |
| MAX6320PUK45CY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.500V, reset timeout(min) 140ms, watchdog timeout(typ) 1.6sec |
| MAX6807XR46-T | MaximIC | Voltage detector. Reset output active-high, push-pull. Threshold reset 4.6V |
