| Parte n. | Fabbricante | Applicazione |
|---|
| MAX9075EXK-T | MaximIC | Low-cost, ultra-small, 3microA, single-supply comparator. |
| MAX6312UK30D3-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 2.925(min) 3.075(max). Nominal timeout period 140ms. |
| MAX806TCPA | MaximIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 3.075V. Active-low reset. Manual reset input. Backup-battery switch. Power-fail threshold accuracy +-2%. Power-fail comparator. Reset window +-2% |
| MAX140EQH | MaximIC | 3 1/2 digit A/D converter with bandgap reference and charge-pump voltage converter |
| MAX6319LHUK33B-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 3.300V, reset timeout(min) 20ms |
| MAX776ESA | MaximIC | -15V or adjustable, high-efficiency, low IQ inverting DC-DC controller |
| MAX797ESE | MaximIC | Step-down controller with synchronous rectifier for CPU power. 3.3V/5V or adjustable main output. Logic-controlled low-noise mode. |
| IH5047C/D | MaximIC | General-purpose CMOS analog switch. Quad pole, single throw (4PST) |
| MAX4106ESA | MaximIC | Ultra-low-noise op amp. 350MHz-3dB bandwidth. 5V/V. |
| MAX708ESA | MaximIC | Low-cost, microprocessor supervisory circuit. Active-high reset output. Precision supply-voltage monitor 4.4V. |
| REF02HJ | MaximIC | +5V precisioon voltage reference. Max TEMPCO 25ppm/degC. Initial error +-25mV |
| MAX391C/D | MaximIC | Precision, quad, SPST analog switch |
| MAX6318MHUK44CW-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.390V, reset timeout(min) 140ms, watchdog timeout(typ) 6.3ms |
| MXD1005SA100 | MaximIC | 5-tap silicon delay line |
| MAX6316LUK48DW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.800V, min reset timeout 1120ms, typ watchdog timeout 6.3ms |
| MAX4581C/D | MaximIC | Low-voltage, CMOS analog multiplexer (8-channel). |
| MAX6509HAUK-T | MaximIC | Resistor-programmable temperature switch. |
| MAX113C/D | MaximIC | 3 V, 400 ksps, 4-channel, 8-bit ADC |
| MAX6348XR43-T | MaximIC | Microprocessor supervisory circuit (reset output active-low, open-drain). Reset threshold (typ) 4.300V. Order increment 10k |
| MAX6317HUK40DX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 4.000V, min reset timeout 1.12sec, typ watchdog timeout 102ms |
| MAX6332UR20D3-T | MaximIC | Ultra-low-voltage, low power microprocessor reset circuit. Reset threshold(typ) 2.0V, reset timeout(min) 100ms. Standard version . |
| MAX6315US35D1-T | MaximIC | Open-drain microprocessor reset circuit. Reset threshold(nom) 3.50V. Reset timeout period(min) 1ms. |
| DG305AC/D | MaximIC | CMOS dual and quad analog switch. |
| ICL7650CTV | MaximIC | Chopper-stabilized amplifier |
| MAX7407CSA | MaximIC | 8-th-order, lowpass, elliptic, switched-capacitor filter. Filter response elliptic (r=1.2), operating voltage +3V |
| MAX6322HPUK40D-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.000V, reset timeout(min) 1120ms |
| MAX6318LHUK42CW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.200V min, reset timeout 140ms,typ watchdog timeout 6.3ms |
| MAX662ACPA | MaximIC | +12V, 30mA flash memory programming supply |
| MAX6318MHUK48AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 4.800V, reset timeout(min) 1ms, watchdog timeout(typ) 25.6sec |
| MAX6317HUK34AX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.400V, min reset timeout 1ms, typ watchdog timeout 102ms |
