| Parte n. | Fabbricante | Applicazione |
|---|
| MAX4566EEE | MaximIC | Two dual SPST switches, low-voltage, bidirectional RF/video switch. |
| MAX6320PUK26BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 2.630V, reset timeout(min) 20ms, watchdog timeout(typ) 25.6sec |
| MAX4512CPE | MaximIC | Quad, Rail-to-Rail, fault-protected, SPST analog switch. |
| MX7523LCWE | MaximIC | CMOS 8 bit multiplying D/A converter. Error 1/8LSB |
| DG200ACJ | MaximIC | Dual monolithic SPST CMOS analog swith |
| MAX6309UK40D2-T | MaximIC | Multiple-input, programmable reset IC (push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,manual-reset input).Factory-trimmed reset thresholds 3.900(min),4.100(max) Nominal timeout period 20ms. |
| MAX6318LHUK47BY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input, reset output active-low, push/pull; active-high,push/pull).Factory-trimmed reset threshold (typ) 4.700V, min reset timeout 20ms, typ watchdog timeout 1.6sec |
| MAX793REPE | MaximIC | Microprocessor supervisory circuit. Reset threshold 2.55V to 2.70V. Active-low reset.Active-high reset.Low-line early warning output.Backup-battery switchover.External switch driver.Power-fail comparator.Battery OK output.Watchdog input.Manual reset inp. |
| MAX6319LHUK34C-T | MaximIC | Microprocessor supervisory circuit with manual reset (manual reset input, reset outputs active-low,push/pull and active-high, push/pull).Factory-trimmed reset threshold(typ) 3.400V, reset timeout(min) 140ms |
| MAX4530CPP | MaximIC | Low-voltage, CMOS analog ICs configured as an 8-channel multiplexer. |
| MAX271MRG | MaximIC | Digitally-programmed, dual 2nd-order continuous lowpass filter. |
| MX7535JCWI | MaximIC | Microprocessor-compatible, 14-bit DAC. INL +-2 LSB. |
| MAX751C/D | MaximIC | +5V-output, step-up, current-mode PWM DC-DC converter. |
| MAX750ACSA | MaximIC | Adjuistable, step-down, current-mode PWM regulator. Inputs from 4V to 11V, up to 450mA load currents. |
| MAX6320PUK32BW-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.200V, reset timeout(min) 20ms, watchdog timeout(typ) 6.3ms |
| MAX6321HPUK39CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.900V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
| MAX4631CPE | MaximIC | Fault-protected, high-voltage, dual analog switch (two NO SPST switches). Fault protection +-40V with power off, +-36V with +-15V supplies. |
| MAX6316LUK31BX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.080V, min reset timeout 20ms, typ watchdog timeout 102ms |
| MAX516BENG | MaximIC | Quad comparator with programmable threshold. Error (LSB) +-2 |
| MAX3096EPE | MaximIC | +-15kV ESD-Protected, 10Mbps, 5V quad RS-422/RS-485 receiver. |
| MAX1487CSA | MaximIC | Low-power, slew-rate-limited RS-485/RS-422 transceiver. Half-duplex. Data rate 2.5Mbps. Slew-rate limited - no. Low-power shutdown - no. Receiver/driver enable - yes. Quiescent current - 230 microA. Number of transmitter on bus - 128. |
| MAX6316LUK38CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.800V, min reset timeout 140ms, typ watchdog timeout 25.6sec |
| MX7575J/D | MaximIC | CMOS, microprocessor-compatible, fast conversion time 5 microsec, 8-bit ADC. INL +-1 LSB. |
| MAX4513CSE | MaximIC | Quad, Rail-to-Rail, fault-protected, SPST analog switch. |
| MAX6310UK33D1-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output,factory-set reset threshold on Vcc,1 additional undervoltage reset input,negative overvoltage reset input).Factory-trimmed reset thresholds 3.218(min),3.383(max). Nominal timeout period 1ms. |
| MAX236EWG | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX364EPE | MaximIC | Precision, quad, SPST, normally closed (NC) analog switch. |
| MAX952EPA | MaximIC | Ultra low-power, single-supply Op Amp + comparator + reference. Internal 1.2V+-2% bandgap reference. Op Amp gain stability 10V/V. Supply current 7microA. |
| MAX6808XR26-T | MaximIC | Voltage detector. Reset output active-low, open-drain. Threshold reset 2.6V |
| MAX6318MHUK26AZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 2.630V, reset timeout(min) 1ms, watchdog timeout(typ) 25.6sec |
