| Parte n. | Fabbricante | Applicazione |
|---|
| MAX4528C/D | MaximIC | Low-voltage, phase-reversal analog switch. |
| MAX4558EEE | MaximIC | +-15kV ESD-protected, low-voltage, CMOS analog multiplexer. |
| ICL7622BCJD | MaximIC | Dual operational amplifier, 5mV |
| MAX628MJAD | MaximIC | Dual power MOSFET driver contains one inverting and one non-inverting section. |
| OP37EJ | MaximIC | Low-noise precision operational amplifier. 63MHz gain-bandwidth product. 17V/micros slew rate. |
| MAX378CWG | MaximIC | High-voltage, fault-protected analog multiplexer. |
| MAX6317HUK35CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.500V, min reset timeout 140ms, typ watchdog timeout 25.6sec |
| MAX529CWG | MaximIC | Octal, 8-bit, serial DAC with output buffer. Single +5V or dual +-5V supply operation. |
| MAX6317HUK25CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 2.500V, min reset timeout 140ms, typ watchdog timeout 25.6sec |
| MAX4566ESE | MaximIC | Two dual SPST switches, low-voltage, bidirectional RF/video switch. |
| MAX4662EPE | MaximIC | 2.5om, quad, SWPST, CMOS analog switch (four NO switches). |
| MAX921MJA | MaximIC | Single micropower, low-voltage comparator. Internal 1.182V+-1% voltage rsference Internal programmable hysteresis. |
| DG405DK | MaximIC | Improved, dual, DPST, NO, high-speed analog switch. |
| MAX6318LHUK45DX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 4.500V min, reset timeout 1.12sec,typ watchdog timeout 102ms |
| MAX4274BFESA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 25, 1+ (Rf/Dg) noninverting gain 26, -3dB BW 580kHz. |
| MAX6318MHUK32DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.200V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX6318LHUK26DY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset,(watchdog input,reset output active-low,push/pull; active-high,push/pull).Factory-trimmed reset threshold(typ) 2.630V min, reset timeout 1.12sec, typ watchdog timeout 1.6sec |
| MAX3087ESA | MaximIC | Fail-safe, high-speed (10Mbps), slew-rate-limited RS-485/RS-422 transceiver |
| MAX883ESA | MaximIC | 5V or adjustable, low-dropout, low current, 200mA linear regulator. 1microA(max) shutdown(OFF) mode. |
| MAX6379UR33-T | MaximIC | Ultra-low-power voltage detector, 3.3V |
| MAX6320PUK47DY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 4.700V, reset timeout(min) 1.12sec, watchdog timeout(typ) 1.6sec |
| MAX6316LUK49CX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reser input,reser output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.900V, min reset timeout 140ms, typ watchdog timeout 102ms |
| MAX998EUT-T | MaximIC | Single, single-supply, high-speed, low-power comparator. |
| MAX697EJE | MaximIC | Microprocessor supervisory circuit. Onboard gating of chip enable signals. |
| MAX427CPA | MaximIC | Low noise, high-precision op amp. |
| MAX138EQH | MaximIC | 3 1/2 digit A/D converter with bandgap reference and charge-pump voltage converter |
| MAX4518EPD | MaximIC | Precision, 4-channel, low-voltage, CMOS analog multiplexer. Single-supply operation (+2.2V to +15V) or bipolar-supply operation (+-2.2V to +-8V). |
| MAX459CQH | MaximIC | 8 x 4 video crosspoint switch with buffers |
| MAX6317HUK31BY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-high, push/pull).Factory-trimmed reset threshold (typ) 3.080V, min reset timeout 20ms, typ watchdog timeout 1.6sec |
| MAX4600CAE | MaximIC | 1.25om, dual SPST, CMOS analog switch. One NC (normally closed) and one NO (normally open) switch. |
