| Parte n. | Fabbricante | Applicazione |
|---|
| MAX3222EUP | MaximIC | 3.0V to 5.5V, low-power, up to 1Mbps, true RS-232 transceiver using four 0.1microF external capacitor. Low supply current 300microA. Guaranteed data rate 120kbps. |
| MXD1000SA125 | MaximIC | 5-tap silicon delay line |
| MAX6318MHUK32DW-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.200V, reset timeout(min) 1.12sec, watchdog timeout(typ) 6.3ms |
| MAX163CEWG | MaximIC | CMOS 12-bit A/D converter with track-and-hold. Error +-1 LSB. |
| MAX6316LUK45CX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.500V, min reset timeout 140ms, typ watchdog timeout 102ms |
| MAX3491C/D | MaximIC | 3.3V-powered, 10Mbps and slew-rate-limited true RS-485/RS-422 transceiver. Guaranteed data rate 10Mbps. Supply voltage 3.0V to 3.6V |
| MAX1426EAI | MaximIC | 10-bit, 10Msps ADC |
| MAX674CTV | MaximIC | +10V precision voltage reference. Temp. coefficient ppm/degC 12. Initial error 15mV |
| MAX6312UK27D1-T | MaximIC | Multiple-input, programmable reset IC(push/pull reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual-reset input). Factory-trimmed reset thresholds 2.633(min) 2.768(max). Nominal timeout period 1ms. |
| MAX6318MHUK34BZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.400V, reset timeout(min) 20ms, watchdog timeout(typ) 25.6sec |
| MAX708MJA | MaximIC | Low-cost, microprocessor supervisory circuit. Active-high reset output. Precision supply-voltage monitor 4.4V. |
| MAX6250BEPA | MaximIC | Low-noise, precision, +5V output voltage reference. Max TEMPCO (ppm/C) 7.0. |
| MAX6351TYUT-T | MaximIC | Dual-voltage microprocessor supervisory circuit with manual reset. Reset threshold 3.08V (Vcc5) and 2.19V (Vcc3). Active-low push-pull reset output 5V and 3V. |
| MAX244CQH | MaximIC | +5V-powered, multichannel RS-232 driver-receiver. |
| MAX6318MHUK37DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.700V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX704SCSA | MaximIC | 3.0V or 3.3V microprocessor supervisory circuit. Reset threshold 2.925V. Active-low reset. Manual reset input. Backup-battery switch. Power-fail threshold accuracy +-4%. Power-fail comparator. Reset window +-75mV |
| MAX4598EWP | MaximIC | Low-voltage, CMOS analog IC, combination single-ended 8-to-1/differential 4-to-1 multiplexer. |
| MAX4052ACSE | MaximIC | Low-voltage, CMOS analog multiplexer |
| MX7547TQ | MaximIC | CMOS parallel loading dual 12 bit multiplying D/A converter. Gain error +-3 LSB. |
| MAX6316LUK40CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 4.000V, min reset timeout 140ms, typ watchdog timeout 25.6sec |
| MAX792LCSE | MaximIC | Microprocessor and non-volatile metory supervisory circuit. Reset threshold 4.62V |
| MAX6380XR34-T | MaximIC | Ultra-low-power voltage detector, 3.4V |
| MAX148BEPP | MaximIC | +2.7V to +5.25V, low-power, 8-channel, serial 10-bit ADC. INL(LSB) +-1. |
| MAX649MJA | MaximIC | 5V or adjustable, high-efficiency, current-limited control scheme, step-down DC-DC controller. |
| ICL7632BCPE | MaximIC | Triple operational amplifier, 5mV |
| MAX4274AGEUA | MaximIC | Dual, Rail-to-Rail, GainAmp op amp with precision internal gain-setting resistors. Rf/Rg inverting gain 2, 1+ (Rf/Dg) noninverting gain 3, -3dB BW 970kHz. |
| MAX410CPA | MaximIC | Single, 28MHz, low-noise, low-voltage, precision op amp. |
| MAX6321HPUK44AX-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 4.390V, reset timeout(min) 1ms, watchdog timeout(typ) 102ms |
| MAX706RCSA | MaximIC | Low-cost, microprocessor supervisory circuit. Precison supply-voltage monitor 2.63V. Active-low reset output signal. |
| MAX542ACPD | MaximIC | +5V,serial-input, voltage-output, 16-bit DAC. INL (LSB) +-1 |
