| Parte n. | Fabbricante | Applicazione |
|---|
| MAX706CUA | MaximIC | Low-cost, microprocessor supervisory circuit. Active-low manual reset input. Independent watchdog timer - 1.6s timeout. Precision supply-voltage monitor 4.4V. |
| MAX750AC/D | MaximIC | Adjuistable, step-down, current-mode PWM regulator. Inputs from 4V to 11V, up to 450mA load currents. |
| MAX456C/D | MaximIC | 8 x 8 video crosspoint switch. |
| MAX465EWG | MaximIC | Two-channel, triple RGB switch and buffer. Voltage gain 2V/V. |
| MAX603MJA | MaximIC | 5V or adjustable, low-dropout, low quiescent currrent, 500mA linear regulator. |
| MAX7705CPA | MaximIC | Microprocessor power-supply monitor with reset |
| MAX6320PUK31DZ-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.080V, reset timeout(min) 1.12sec, watchdog timeout(typ) 25.6sec |
| MAX6315US43D1-T | MaximIC | Open-drain microprocessor reset circuit. Reset threshold(nom) 4.30V. Reset timeout period(min) 1ms. |
| MAX6334UR25D2-T | MaximIC | Ultra-low-voltage, low power microprocessor reset circuit. Reset threshold(typ) 2.5V, reset timeout(min) 20ms. |
| MAX1488ECPD | MaximIC | +,-15kV ESD-protected, quad, low-power RS-232 line driver |
| MAX166DEPP | MaximIC | CMOS microprocessor-compatible, 5 microsec, 8-bit ADC. Error +-1 LSB. |
| MAX6307UK32D2-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output,factory-set reset threshold on Vcc,1additional undervoltage reset input,negative/overvoltage reset inp.).Factory-trimmed reset thresholds3.120(min),3.280(max).Nominal timeout period 20ms. |
| MAX6318MHUK36CZ-T | MaximIC | Microprocessor supervisory circuit with watchdog input (watchdog input,reset output active-high,push/pull and active-low, bidirectional).Factory-trimmed reset threshold(typ) 3.600V, reset timeout(min) 140ms, watchdog timeout(typ) 25.6sec |
| MAX6321HPUK39DX-T | MaximIC | Microprocessor supervisory circuit with watchdog (watchdog input, reset outputs active-high, push/pull and active-low, open-drain).Factory-trimmed reset threshold(typ) 3.900V, reset timeout(min) 1.12sec, watchdog timeout(typ) 102ms |
| MAX821PUS-T | MaximIC | Microprocessor voltage monitor with pin-selectable power-on reset timeout delay (1ms,max, 20ms,min or 100ms,min). Reset threshold(nom) 4.00V. Active-low reset output. |
| DG381ABWE | MaximIC | General purpose CMOS quad analog switch. |
| MAX8885EUK50 | MaximIC | 150mA, low-dropout, linear regulator with power-OK output. Preset output voltage 5.0V. |
| MAX151ACWG | MaximIC | 300kHz 10-bit A/D converter with reference and T/H. TUE 1.0 LSB. |
| MAX3082CSA | MaximIC | Fail-safe, high-speed (10Mbps), slew-rate-limited RS-485/RS-422 transceiver |
| MAX391CSE | MaximIC | Precision, quad, SPST analog switch |
| MAX4573EAI | MaximIC | Serially controlled, clickless audio/video switch. 3-wire, SPI/QSPI/MICROWIRE - compatible. |
| MAX6306UK30D2-T | MaximIC | Multiple-input, programmable reset IC (open-drain reset output, factory-set reset threshold on Vcc, 1 additional undervoltage reset input, manual reset input). Factory-trimmed reset thresholds 2.925(min),3.075(max) Nominal timeout period 20ms. |
| MAX2903EGI | MaximIC | 200mW single-chip transmitter IC for 868/915 MHz ISM band |
| MAX157AMJA | MaximIC | +2.7V, low-power, 2-channel, 108ksps, serial 10-bit ADC in 8-pin microMAX. INL (LSB) +,- 0.5 |
| MAX664MJA | MaximIC | Dual Mode 5V or programmable micropower voltage negative regulator. |
| MAX805LCSA | MaximIC | Microprocessor supervisory circuit. 4.65V precision supply-voltage monitor |
| MAX6320PUK36DX-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input, reset output active-low, open-drain).Factory-trimmed reset threshold(typ) 3.600V, reset timeout(min) 1.12sec, watchdog timeout(typ) 102ms |
| MAX324EPA | MaximIC | Precision, single-supply, SPST analog switch. |
| MAX6316LUK31AY-T | MaximIC | Microprocessor supervisory circuit with watchdog and manual reset (watchdog input,manual reset input,reset output active-low,push/pull).Factory-trimmed reset threshold (typ) 3.080V, min reset timeout 1ms, typ watchdog timeout 1.6sec |
| MAX494CSD | MaximIC | Quad, micropower, single-supply operation (+2.7V to +6V), Rail-to-Rail op amp. |
